Aqua Meds FlukeGuard

FlukeGuard™ Directions

Step 1: Determine the Dosage

Using the chart below, calculate the amount of FlukeGuard needed based on your pond’s volume:

Step 2: Prepare the Solution

• Measure the required amount of FlukeGuard using an accurate scale.
• Mix the measured FlukeGuard in a container of warm water (not hot) and stir into a slurry.

Step 3: Apply to the Pond

• Slowly pour the dissolved FlukeGuard solution into the pond.
• Add it near the return or aeration system to help distribute the medication evenly.

Step 4: Monitor the Pond

• Keep aeration running throughout treatment to maintain oxygen levels.
• Observe your koi for signs of stress or unusual behavior.

Step 5: Repeat if Necessary

• For heavy infestations, a second dose may be applied after 7 days using the same procedure.

Precautions

• Do Not Overdose: Overdosing can lead to fish fatalities.
• Avoid Concurrent Medications: Do not use FlukeGuard with other treatments.
• Turn Off Equipment: Turn off UV sterilizers, ozone generators, protein skimmers, and carbon filters for the full 7-day treatment period.
• Handle with Care: Always wear gloves and goggles when handling FlukeGuard.

Storage

Store above 50°F and keep out of reach of children. Use within three months of opening for best effectiveness.

By following these instructions, you’ll safely and effectively treat your pond, helping your koi stay healthy and parasite-free!

FlukeGuard™ Safety Precautions

• Keep Out of Reach of Children: Store FlukeGuard in a secure location inaccessible to children.
• For Animal Treatment Only: This product is intended exclusively for treating fish and should not be used for any other purpose.
• Wear Protective Gear: Always wear protective gloves and goggles when handling FlukeGuard to prevent skin and eye contact.
• Avoid Concurrent Medications: Do not use FlukeGuard in conjunction with other medications to prevent adverse reactions.
• Proper Storage: Store FlukeGuard at temperatures above 50°F (10°C) to maintain its efficacy.
• Sensitive Species Warning: FlukeGuard is harmful to aquatic snails and stingrays; avoid use in environments containing these species.
• Prevent Overdosing: Carefully measure the appropriate dosage to avoid overdosing, which can lead to fish fatalities.
• Maintain Adequate Aeration: Ensure proper aeration during treatment, as FlukeGuard can reduce dissolved oxygen levels.
• Monitor Water Quality: Regularly check water parameters to detect any adverse changes during treatment.
• Observe Fish Behavior: Keep a close watch on your fish for any signs of stress or unusual behavior during and after treatment.

By following these precautions, you can help ensure a safe and effective treatment process for your aquatic life.

FlukeGuard vs Aqua Prazi – What's the Difference?

FlukeGuard and Aqua Prazi are both highly effective treatments for flukes and internal parasites, but they work in different ways. Here's a quick comparison to help you decide which one to use:

When to Use Each

• Start with FlukeGuard as a general fluke treatment or in cooler water.
• Use Aqua Prazi when targeting tapeworms or as a follow-up to FlukeGuard.
• Alternate treatments if flukes persist after initial dose or to ensure broad parasite control.

Instructions for Using Terminate™ With FlukeGuard™

Alternate Aqua Meds Protocol: When treating for both common protozoan parasites and flukes, FlukeGuard™ may be combined with the third and final Terminate™ treatment as described below.

• Day 1:
  • Water Change: Perform a 25% or larger water change before treatment.
  • Dosage: Add 100 mL of Terminate™ per 1,000 gallons of pond water.
  • Aeration: Increase aeration and water circulation, if possible.
• Day 2 (Approximately 24 Hours Later):
  • Water Change: Perform another 25% or larger water change before treatment.
  • Dosage: Add 100 mL of Terminate™ per 1,000 gallons of pond water.
  • Aeration: Continue increased aeration and water circulation.
• Day 3 (Approximately 24 Hours Later):
  • Water Change: Perform another 25% or larger water change before the final treatment.
  • Preparation: In a clean container, combine:
    • 100 mL of Terminate™ per 1,000 gallons of pond water
    • 3 grams of FlukeGuard™ per 1,000 gallons of pond water
    Mix thoroughly until the FlukeGuard™ is well dispersed.
  • Application: Distribute the mixture around the pond in areas of good water circulation so it disperses evenly throughout the system.
  • Aeration: Maintain strong aeration and water circulation.
• After the Day 3 Terminate™ + FlukeGuard™ Treatment:
  • Water Changes: Do not perform water changes for 5 full days after the combined treatment.
  • Pond Maintenance: Avoid routine pond maintenance that would remove or significantly dilute the FlukeGuard™ during this 5-day period.
  • Aeration: Continue good aeration and water circulation.

Water Conditioner Compatibility

When treating replacement water containing chlorine or chloramine, use a simple sodium thiosulfate-based dechlorinator such as Aqua Meds® Just Dechlor™ or Aqua Meds® Armor™. Avoid water conditioners that bind or detoxify ammonia or sulfoxylate-based water conditioner formulas during Terminate™ treatment, as they may interfere with the treatment chemistry.

Additional Treatment Notes

• Run normal biological filtration and maintain good water circulation throughout treatment.
• Turn off UV sterilizers and ozone during treatment.
• Remove activated carbon and other chemical filtration media.
• Avoid using salt during Terminate™ treatment. If salt is already present, the level should not exceed 0.05%.
• Use only at water temperatures of 50°F or higher.

Storage

• Store Terminate™ between 50°F and 110°F.
• Store FlukeGuard™ in a cool, dry location in its tightly closed original container.

Note: The Terminate™ and FlukeGuard™ combination provides broad-spectrum treatment for many common protozoan parasites, external fungus, and skin and gill flukes. Always know your true pond volume and measure each treatment accurately.